Scion xB 2011 Remote Key
Toyota Remote Key (ID67) 12BBY
Overview
Key Type
Remote Key
Markets
EU, AUO, MEA, ASIA, USA
Transponder
ID67 (Texas 4D67)
Separate
Frequency
315 MHz433 MHz
Battery
CR2016
Transponder Cloning
Yes
Skill Level
Beginner
Universal Keys
Xhorse ID 0507 802
Test failed
Original Keys
12BBY 2Buttons 433MHz TOY43: Toyota Auris 2007-2013, Corolla 2007-2013, Hiace 2006-2013, Previa 2006-2015, Rav4 2006-2013, Tarago 2006-2016, Wish 2004-2010.
Direct Programming to another vehicle
12BBY 3Buttons w/t trunk 433MHz TOY43: Toyota Prado 2010-2015.
Direct Programming to another vehicle
12BBY 3Buttons w/t Panic 315MHz TOY43: Toyota RAV4 2006-2011, Scion xB 2008-2013.
Direct Programming to another vehicle
12BBY 4Buttons 315MHz TOY43: Toyota Camry 2006-2011, Corolla 2009-2010.
Direct Programming to another vehicle
Overview
Add key
OBD
All keys lost
OBD
Prepare dealer key
No
Remote programming
Manual
All keys erased automatically
Not specified
Power supply
Recommended (if under 11.5V)
Additional cables required
No
Number of key slots
5
Key Programming via OBD
General Instructions
- Toyota’s master key system distinguishes between master keys and valet (sub) keys in the vehicle’s immobilizer and key programming system. Master keys are required when adding or programming new keys with normal OBD procedure.
- Master Keys (P1): B2, 32, 35. Valet keys (P1): D2, 92.
- With all keys lost, programming requires reseting immobilizer system (tested with Abrites ok). If you cannot reset system, programming must be done via eeprom.
Key Programming via EEPROM
Units - Immobox
Original transponder: TIRIS 4D (ID67, 68, 70)
Allowed transponder: TIRIS 4D (ID60, 61, 63, 64, 67, 68, 70)
Data location: 93C66
Reading: in circuit, out circuit
Adapters: Autel APB-129_V1, APA-103; VVDI Eeprom Clip etc.
Heating temperature: 300°C
No. of keys: 8
Unit location
Located behind the central console (to get access may need to remove the entire panel)
Data location
Eeprom 93C66
Eeprom reading (Out-circuit)
Use EEPROM adapters for reading; most programmers can handle the readout.
Eeprom reading (In-circuit)
Use a solder-free EEPROM adapter from Autel, Xhorse or any other brand - all of them can handle the reading. If the readout fails, it means the contact is poor - go over each pin with a soldering iron and try again.
Remote Manual Programming
NOTE Make sure the power is OFF and the driver's door is open
NOTE This instruction must be completed within two minutes
- Insert and remove key from ignition TWICE.
- CLOSE and OPEN the driver's side door TWICE - leaving the door in OPEN position.
- Insert and remove key from ignition ONCE.
- CLOSE and OPEN the driver's side door TWICE - leaving the door in OPEN position.
- Insert the key and close driver door.
- Turn ignition ON and OFF. Do not start the vehicle.
- Remove the key from ignition. Door locks will cycle ONCE to indicate programming mode is active.
- PRESS and release both LOCK and UNLOCK buttons on the remote control for 2 seconds.
- PRESS and release the LOCK button on the remote control for one second. Door locks will cycle ONCE to indigate successful programming. (NOTE: if the locks cycle TWICE remote control might be incorrect for the vehicle).
- Repeat steps 8 and 9 for any additional remotes.
- Turn ignition ON and OFF to exit programming mode.
Toyota Manual Remote Programming
Programmers
Autel
Immobilizer Programming
Xhorse
Immobilizer Programming
Abrites AVDI
Immobilizer Programming
Smart Pro
Immobilizer Programming
TDB1000
Not supported
Code Series
10001-15000 (Toyota, Hino) 8-8 Cuts 1-5000 (Chevrolet, GM, Toyota) 8-8 Cuts 50000-69999 (Toyota, Pontiac, Scion) 10-10 Cuts
Overview
Double locked
No
Opening direction (LHD)
Counter-clockwise
Decoder capability
Door LockIgnitionBoot/Trunk
Decoding Tips
- Lishi TOY43 is for 8-8 cut keys
- Lishi TOY43AT is for 10-10 cut keys
- There is separate Lishi tool for ignition and door locks.
- To decode the lock read in the SAME direction as it was picked.
Keys with 10 cuts:
- There are two versions: ISN 444 → 4 is deepest cut, ISN 7625 → 1 is deepest cut.
- Adjacent cuts WITHIN the pairs must be no more than one depth apart.
- Adjacent cuts BETWEEN the pairs must be no more than two depths apart.
- No more than three consecutive cuts of the same depth.
- Number stamped on some wafers are opposite to its corresponding cut depth.
Overview
Original key glued
No
Synchronizing
No
Repair Instructions
- Key has separate immobilizer chip.
- There is no need to synchronize or reprogram the key after replacing the battery.